Skip to main content

Filter By:

  • Show More Brands

  • Show Fewer Brands
  • Show More Sizes
  • Show Fewer Sizes

Tools

$18.95
Park's AV-1 Axle Vise makes repairing and overhauling hubs easier than ever. It prevents your axle from spinning while work is done on the hub and it has two different size receptacles so it will work with both front and rear axles.
$23.95
The BBT-22 is a shop-quality tool for installing and removing Shimano and ISIS Drive splined 20-tooth bottom bracket cups. Made from investment-cast steel, the BBT-22 ensures maximum engagement with the bottom bracket cup. It can be used with a 3/8-inch drive torque wrench, a 3/8-inch ratchet driver, a 32mm wrench, the Park FRW-1 Freewheel Remover Wrench (sold separately), or a 1-inch wrench.
$127.95
The BKD-1.2 Hydraulic Brake Bleed Kit will bleed most models of DOT fluid-based hydraulic disc brakes, including models made by SRAM®, Formula®, Hayes®, and Hope®. Bleeding of hydraulic brakes removes air bubbles and contaminants from the braking system, for long-lasting components and peak performance. The BKD-1.2 is built for the rigors of daily commercial use and includes two syringes, hoses with shutoff clips, multi-size bleed blocks, and a set of our unique mountable syringe holders, as well as multiple hose fittings to fit the multiple standards found on hydraulic bicycle brake systems. Every part is replaceable and available from Park Tool. Housed in a rugged storage case. Includes: - Two 20 mL syringes Two hose assemblies with shutoff clips - Two 10 mm/12 mm universal bleed blocks - Two 11 mm bleed blocks for Hayes® systems -  Two adjustable syringe holders -  M5 x 0.8 adapters— SRAM® (x2) -  M6 x 1.0 adapter— universal (x2) - Bleeding Edge-specific fitting — SRAM® -  Hose compression sleeve — universal -  Set of spare O-rings and hose -  Replacement parts available -  Brake fluid not included NOTE: The BKD-1.2 is for DOT fluid-based hydraulic bicycle brake systems only. DOT fluid and mineral oil should never be mixed in the brake system or in their respective service tools. Cross-contamination of brake fluid may cause seal failure which may result in brake failure. For mineral oil brake systems use the Park Tool BKM-1.2 Hydraulic Brake Bleed Kit — Mineral Oil.
$35.99
Park's Bottom Bracket Bearing Tool Set removes and installs (with a bearing press, which is sold separately) BB30, PF30, EVO 386 and BBright bottom bracket bearings. This fine tool slides through the bottom bracket shell and into the bearings so the bearings can be tapped out with a hammer. Two bushings for installing BB30 and PF30 bearings from SRAM and FSA are included (press required and sold separately).
$16.95
The CC-4 is a drop-in style gauge that measures bicycle chain wear. The laser cut CC-4 accurately measures a long section of chain and strategically comes in contact with the chain in three places, quickly and easily taking the guesswork out of knowing when chain replacement is necessary. A worn chain will cause poor shifting as well as accelerate drivetrain wear. The tool works on any 5 to 12-speed derailleur chain (including SRAM AXS) and is designed to accurately indicate when a chain reaches .5% and .75% wear, the points at which most chain manufacturers suggest replacement.
$45.95
A fast and convenient tool to remove and install 12-spline Shimano/SRAM style cassette lockrings, as well as similar lockrings on rotor discs. The FR-5H features a modified FR-5 tool that allows use without removing most quick release skewer nuts. The removable, threaded steel handle makes it possible to replace a worn or damaged head. - Fits Shimano, SRAM (including 1x), SunRace, SunTour, Chris King and other cassette lockrings - Also fits some Shimano disc brake lockrings
$8.95
Park's Double-Ended Cone Wrenches are designed for home mechanics. They're made of thin tool steel to fit the low-clearance adjusting nuts and cone flats on a variety of bearing assemblies. Each wrench is chrome plated for long life and available in popular combinations from 11 to 18mm. Most applications require a pair of cone wrenches. Call or stop by. We can recommend the correct sizes for your needs.
$20.99
Also called a sleeping hub, the Dummy Hub slides into rear dropouts and replaces the rear wheel for chain cleaning and transport. The DH-1 works with all derailleur and 1/8" chain. The unique design allows the bike to be shifted and works with open dropout and thru-axle frames up to 12mm.
$8.95
The Park FR-7 Freewheel Remover fits Falcon freewheels. It's built thin so that removing axle parts is unnecessary. And, it's constructed of durable heat-treated steel.
This dual-sided brush is specifically designed for cleaning hard-to-reach areas of the bicycle drivetrain. The long, stiff bristles of the GSC-3 are narrow enough to reach between the gears of tightly-spaced modern cassettes, while the slim contoured end is capable of picking grit and grime out of tight spaces such as derailleur pulley wheels.
$29.99
Made from tough steel and reinforced with extra material at the highly stressed wrench openings, Park’s shop-quality Pedal Wrench is built to easily install and remove pedals, and to last and last. It has 15mm and 9/16-inch precision openings to fit all pedals. And it boasts a long, round, vinyl-coated handle that won’t dig into your hand and provides optimum leverage. There's even a hole in the end of the wrench for hanging it on your toolboard.
$132.95
With today’s lightweight components, torque wrench use in the shop is no longer an option — it’s a must for every mechanic. The TW-6.2 is a high-quality, ratcheting, click-type torque wrench that accurately measures and applies the proper amount of torque to a component’s threaded fastener(s). Designed for higher torque settings for repairs and installation in the bottom bracket, cassette lockring and other areas that use a higher torque settings. For lower torque setting, see the TW-5. Comes with its own protective case. - 10–60 Newton meter range (88–530 Inch Pounds) - Adjustable in 0.25 Nm increments - Ratcheting 3/8" drive - Reads and registers for both left hand and right hand threading - Dial-adjust system allows desired torque setting to be preset - Calibrated to be accurate to +/- 4% - Length: 36.2cm (14.25")
$35.99
True your wheels right from your bicycle repair stand with Park's Repair Stand-Mounted Wheel-Truing Stand. It's comprised of two parts. One piece is an axle holder for you to securely attach your wheel (accepts all wheel diameters and rim widths) via your quick release or axle nuts. The other piece attaches on the stand near the rim and acts as a pointer that shows where the wheel needs truing. This small, light truing stand installs quickly and easily on Park's PRS-25 and PCS-10 repair stands, and also Park's PCS-1 and PCS-4 stands when they are used with the adjustable-height extension.
$15.99
Park Tool's CTP-4K includes four replacement chain tool pins and one 5/32" ball bearing. To replace the chain tool pin, unscrew the cap, and pull out the old pin. Use care not to lose the ball bearing beneath the pin. Install the new pin and replace the cap. Works with the CT-4.3, CT-4.2, CT-4, and CT-11
$35.95
Updated to fit current 12-speed cassettes, this combination chain whip and freewheel / lockring remover wrench is heat treated to prevent bending, flexing and wear and features a long, molded handle in addition to a built in hex shaped driver. - Works on 5- to 12-speed road and mountain bike cassettes and freewheels - 1-inch (25.4mm) box-end wrench fits Park Tool Freewheel / Cassette Lockring Tools - Features hardened pins to keep the chain in place
$9.95 - $11.99
Park's Cone Wrenches are made of durable tool steel and are nice and thin to fit on the small-clearance cones found on hubs and other bearing assemblies. Plus, they work as regular wrenches, too. They feature Park's special Y heads that put more material where it's needed for excellent durability and strength. Most applications require at least 2 cone wrenches. If you have questions please contact us and we can recommend the correct sizes for your needs.
$24.95
Park handles all of your screwdriver needs with their Shop Screwdriver Set that includes 3mm and 6mm regular, and #0 and #2 Phillips screwdrivers. They feature heat-treated chrome-vanadium tips and shafts for maximum durability plus dual-density grips for top control and comfort.
$22.99
Designed and built especially for singlespeed bikes, Park's SS-15 Single Speed Spanner is a durable forged-steel tool with a 15mm socket wrench for axle nuts, 15mm open-end wrench for pedals, a tire lever, and a bottle opener. It's just the right size to take along on rides and is great for wrenching in your shop too.
$8.49 - $9.99
Park's professional-quality, precision-sized spoke wrenches are hardened and chrome plated for long service. Wrenches are vinyl coated in one of four colors indicating the size at a glance. You will find these wrenches in virtually every professional bike shop and every shop mechanic's personal tool stash. Make sure you have the sizes you need in your home toolbox and bike bag.
$7.99
The small and handy RR-12.2 Tape Measure features a tough composite housing with an integrated belt clip and both metric and SAE readings up to 350 centimeters or 12 feet. Measurement can be locked in place using the thumb lock or the handy quick-stop button. - Maximum length: 350 cm | 12 ft. - Markings: 1 mm | 1/32" (up to 6") | 1/16" (over 6")
$12.99
Park's Valve Core Tool is great for tightening, removing and installing Schrader and Presta valve cores (the cores are inside the valve), and also Presta valve extenders that have 5mm wrench flats. It's a handy tool to save a tube when all that's wrong is a broken valve, and it also lets you remove valves to easily insert sealant.
$21.95
Park Tool's professional-quality Snap Ring Pliers are made from forged, heat-treated cro-moly steel with a return spring and vinyl-dipped grips. The RP-3 has 1.3mm tips on bent nose blades for medium, external snap rings.
$21.95
Park Tool's professional-quality Snap Ring Pliers are made from forged, heat-treated cro-moly steel with a return spring and vinyl-dipped grips. The RP-2 has 1.3mm tips on bent nose blades for medium, internal snap rings. The tips of the RP-2 open from 22mm down to 2mm (center to center).
$23.95
Park Tool's professional-quality Snap Ring Pliers are made from forged, heat-treated cro-moly steel with a return spring and vinyl-dipped grips. The RP-4 has 1.7mm tips on bent nose blades for larger, internal snap rings. The tips open from 21mm down to 2mm (center to center).
$21.95
Professional quality ring plier made from forged, heat-treated cro-moly steel with a return spring and vinyl dipped grips. The RP-5 has 1.7mm tips on straight blades for small, internal snap rings. The tips open from 22mm to 0 (tips touching).
$32.95
• 15mm L-shaped hex wrench to fit Shimano rear thru-axle freehubs • Through-hardened industrial quality steel • Chamfered tips for a precision fit
$3.95
Refill pack for the Park Tool TPT-1 Tubeless Plug Tire Tool and other similar tools. These vulcanized rubber plugs are used to temporarily repair punctures in tubeless bicycle tire systems. Set of 5. NOTE: Intended for tubeless bicycle tires using sealant only. Not compatible with inner tube systems.
$14.95
Park combines the three most used bolt sizes into one convenient wrench. The 3-Way Sprocket Wrench sports 8, 9 and 10mm sockets made from forged chrome-vanadium steel in Park's classic Y-shape that offers plenty of leverage and a comfortable grip.
$407.94
The Park Tool 758.2 will ream and face the head tubes of bike using the 1.5" standard. The 758.2 is designed for use with the Park Tool HTR-1 or HTR-1B Headtube Facer and Reamer. Must also be used with the 750.2 Centering Cone Adaptor.
$21.95
Forged with Chrome Vanadium (CR-v) steel, precision ground, heat-treated, plated and polished. The PAW-6 opens to 24mm and features a laser engraved measurement scale and dipped blue handle for comfort.
Page 1 of 6 Next page